Agri-fab 45-0418 User Manual Page 5

  • Download
  • Add to my manuals
  • Print
  • Page
    / 40
  • Table of contents
  • TROUBLESHOOTING
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 4
5
ASSEMBLY
REF QTY DESCRIPTION
1 3 Clevis Pin, 1/2" x 3"
2 1 Clevis Pin, 1/2" x 2"
3 4 Hex Bolt, 5/16-18 x 1"
4 4 Hex Bolt, 1/2-13 x 3-1/2"
5 25 Washer, 1/2" x 1-1/2"
6 2 Hex Bolt, 5/16" x 3"
7 4 Hex Bolt, 3/8-16 x 2"
8 4 Hair Pin
9 2 Bowed Washer, 1" x .32"
10 10 Washer, 5/16"
11 12 Hex Bolt, 1/2-13 x 2-1/4"
12 1 Hex Bolt, 1/2-13 x 1-1/2"
13 6 Hex Flange Bolt, 1/4-20 x 1"
14 6 Flanged Lock Nut, 1/4-20
15 18 Nylock Nut, 5/16-18
16 4 Nylock Nut, 3/8-16
REF QTY DESCRIPTION
17 19 Nylock Nut, 1/2-13
18 2 Lock Nut, 1/2-13
19 2 Carriage Bolt, 5/16-18 x 1-3/4"
20 2 Carriage Bolt, 5/16-18 x 1"
21 2 Carriage Bolt, 5/16-18 x 1-1/4"
22 2 Hex Bolt, 5/16-18 x 1-1/2"
23 4 Hex Bolt, 5/16-18 x 1-3/4"
24 2 Spacer, .5" x 1.0" x .59"
25 1 Spacer, .81" x 1.25" x 1.5"
26 1 Nylock Nut, 3/4-10
27 4 Spacer .75" x 1.25" x .5"
28 1 Hex Bolt, 3/4-10 x 7-1/2"
29 2 Hex Bolt, 1/2" x 4-1/2"
30 3 Chute Keeper
31 8 Nylon Tie
32 2 Replacement Shear Bolt
TOOLS NEEDED
(1) 5/16" Wrench
(1) 3/8" Wrench
(1) 7/16" Wrench
(2) 1/2" Wrenches
(2) 9/16" Wrenches
(2) 3/4" Wrenches
(1) 1-1/6" Wrench or Adjustable Wrench
(1) 1-1/8" Wrench or Adjustable Wrench
(1) 3/16" Allen Wrench
(1) Phillips Screwdriver
(1) Scissors or Knife
(1) Grease Gun w/ general purpose grease
(1) 15" Concrete Block
WIRING ASSEMBLY
Assemble (2) handlebar brackets and (1) handlebar 1.
strap onto the handlebars using (2) long, small screws
and (2) small nylock nuts. Do not tighten yet.
OFF
LO
HI
SMALL NYLOCK
NUT
LONG,
SMALL
SCREW
HANDLEBAR
STRAP
HANDLEBAR
BRACKET
Assemble the switch bracket to the handlebar switch 2.
using (2) small whizlock nuts. Tighten.
SMALL
WHIZLOCK
NUT
SWITCH
BRACKET
FIGURE 1
FIGURE 2
Assemble the switch bracket to the handlebar strap 3.
using (1) short, small screw and (1) small nylock nut.
See gure 3. Do not tighten yet.
Rotate handlebar switch until it is at desired angle and 4.
then tighten the screws and nuts assembled in steps
1 and 3.
FIGURE 3
OFF
LO
HI
SHORT,
SMALL
SCREW
SMALL NYLOCK
NUT
Page view 4
1 2 3 4 5 6 7 8 9 10 ... 39 40

Comments to this Manuals

No comments